CAMPUS® datasheet | VESTAMID® EX9350 blk (sw)
This datasheet of VESTAMID® EX9350 blk (sw) from Evonik Industries AG is provided by the international plastics database CAMPUS.
Heat- and weather-resistant, impact-modified polyamide 612 elastomer for extrusion
Resin: ISO 1874-PA612-PPGD,EHL,18-005
VESTAMID® EX9350 is a PA 612 elastomer extrusion compound developed for the manufacturing
of tubing systems, e.g. vacuum brake booster lines.
The compound is in particular suitable for applications, that require a continuous high flexibility
even if subjected to high temperature load. In contrast to conventionally plasticized materials
(plasticizerloss) tubes made from VESTAMID® EX9350 do not stiffen under elevated temperatures.
The compound is especially suitable for the extrusion of tubing systems that are exposed to in-
creased burst pressures and service temperatures.
|Mechanical properties||dry / cond||Unit||Test Standard|
|Tensile Modulus||600 / -||MPa||ISO 527-1/-2|
|Yield stress||30 / -||MPa||ISO 527-1/-2|
|Yield strain||35 / -||%||ISO 527-1/-2|
|Nominal strain at break||>50 / -||%||ISO 527-1/-2|
|Charpy impact strength, +23°C||N / -||kJ/m²||ISO 179/1eU|
|Charpy impact strength, -30°C||N / -||kJ/m²||ISO 179/1eU|
|Charpy notched impact strength, +23°C||110[P]||kJ/m²||ISO 179/1eA|
|Charpy notched impact strength, -30°C||8 / -||kJ/m²||ISO 179/1eA|
Maximum Water Content: 0.1 %
When the indicated water content is exceeded, the resin must be dried. The drying time is dependent
on the drying temperature. At a drying temperature of 80 °C we recommend, depending on the water
content, a drying time of 8 - 16 hours. Fresh air dryers are acceptable, better would be a dry air or
vacuum dryer. Please note our product literature, plasticized resins can lose plasticizer during drying.
Melt Temperature : 210 - 240 °C
All listed technical data are typical values intended for your guidance. They are given without obligation and do not constitute a materials specification. Should you have any further questions concerning material behavior or properties, please contact us at the following address : for PA: Evonik Industries AG PP-HP-CRM Gebäude 1227 / PB 16 D-45764 Marl Phone: +49-(0)2365/49-2720 Fax:+49-(0)2365/49-2070 E-Mail: firstname.lastname@example.org for PMMA: Evonik Industries AG Marketing / Campus Kirschenallee D-64293 Darmstadt Germany Phone: +49 - (0) 61 51 / 18-47 11 Fax: +49 - (0) 61 51 / 18-31 77 E-Mail: email@example.com Internet: http://www.plexiglas-polymers.com
® = registered trademark
PLEXIGLAS® is a registered trademark of Evonik Röhm GmbH, Germany,
outside of the Americas. Within the Americas it is sold as ACRYLITE®,
which is a registered trademark of Evonik Cyro LLC, USA.
PLEXIMID® is a registered trademarks of Evonik Röhm GmbH, Germany.
CYROLITE® and XT® polymer are registered trademarks of Evonik Cyro LLC, USA.
This information and all further technical advice is based on our present knowledge
and experience. However, it implies no liability or other legal responsibility on our part,
including with regard to existing third party intellectual property rights, especially
patent rights. In particular, no warranty, whether express or implied, or guarantee of
product properties in the legal sense is intended or implied. We reserve the right to
make any changes according to technological progress or further developments. The
customer is not released from the obligation to conduct careful inspection and testing
of incoming goods. Performance of the product described herein should be verified by
testing, which should be carried out only by qualified experts in the sole responsibility
of a customer. Reference to trade names used by other companies is neither a
recommendation, nor does it imply that similar products could not be used.
This information and all technical and other advice are based on Evonik’s
present knowledge and experience. However, Evonik assumes no liability for
such information or advice, including the extent to which such information or
advice may relate to third party intellectual property rights. Evonik reserves the
right to make any changes to information or advice at any time, without prior
or subsequent notice. EVONIK DISCLAIMS ALL REPRESENTATIONS AND
WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SHALL HAVE NO LIABILITY
FOR, MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS FOR A PARTICULAR
PURPOSE (EVEN IF EVONIK IS AWARE OF SUCH PURPOSE), OR OTHERWISE.
EVONIK SHALL NOT BE RESPONSIBLE FOR CONSEQUENTIAL, INDIRECT OR
INCIDENTAL DAMAGES (INCLUDING LOSS OF PROFITS) OF ANY KIND. It is the
customer’s sole responsibility to arrange for inspection and testing of all
products by qualified experts. Reference to trade names used by other
companies is neither a recommendation nor an endorsement of the
corresponding product, and does not imply that similar products could not be
Sales range and technical data subject to alteration.
CAMPUS® is a registered trademark of CWFG mbH, Frankfurt am Main, 2012