View list of
  • All DuPont grades
  • All PA* grades
  • All grades beginning with Z

CAMPUS® datasheet | Zytel® HTN53G35HSLRHF BK083


This datasheet of Zytel® HTN53G35HSLRHF BK083 from DuPont Engineering Polymers is provided by the international plastics database CAMPUS.

CAMPUS is organized by a group of leading international resin producers, who have agreed to test their material according to uniform conditions, based on ISO standards (ISO 10350, ISO 11403), in order to offer comparable data to the market.

This datasheet includes:

  Zytel® HTN53G35HSLRHF BK083 | PA*-GF35 | DuPont Engineering Polymers
Product Texts
Common features of Zytel® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature performance, good electrical and flammability properties, good abrasion and chemical resistance.

Zytel® HTN cost effectively bridges the performance gap between conventional engineering resins and high-end specialty polymers – this is especially important when your component or system has to survive in a hot, cold, chemically aggressive and/or load-bearing environments.
Based on aromatic copolymers, Zytel® HTN offers a balance of chemical, moisture and temperature resistance, plus outstanding processability.

The good melt stability of Zytel® HTN normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.

______________________________________________________


Zytel® HTN53G35HSLRHF is a 35% glass fiber reinforced, heat stabilized and lubricated high performance polyamide resin for injection molding in water-heated molds. It has high stiffness, high toughness and improved flow characteristics.

Rheological propertiesdry / condUnitTest Standard
Molding shrinkage (parallel) 0.2 / * % ISO 294-4, 2577
Molding shrinkage (normal) 0.6 / * % ISO 294-4, 2577
Mechanical propertiesdry / condUnitTest Standard
Tensile Modulus 11000 / 11000 MPa ISO 527-1/-2
Stress at break 210 / 180 MPa ISO 527-1/-2
Strain at break 3.2 / 3.4 % ISO 527-1/-2
Tensile creep modulus (1h) * / 6500 MPa ISO 899-1
Tensile creep modulus (1000h) * / 4700 MPa ISO 899-1
Charpy impact strength (+23°C) 70 / 70 kJ/m² ISO 179/1eU
Charpy impact strength (-30°C) 60 / 50 kJ/m² ISO 179/1eU
Charpy notched impact strength (+23°C) 12 / 12 kJ/m² ISO 179/1eA
Charpy notched impact strength (-30°C) 11 / 11 kJ/m² ISO 179/1eA
Thermal propertiesdry / condUnitTest Standard
Melting temperature (10°C/min) 260 / * °C ISO 11357-1/-3
Temp. of deflection under load (1.80 MPa) 226 / * °C ISO 75-1/-2
Vicat softening temperature (50°C/h 50N) 225 / * °C ISO 306
Coeff. of linear therm. expansion (parallel) 24 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion (normal) 65 / * E-6/K ISO 11359-1/-2
Electrical propertiesdry / condUnitTest Standard
Dissipation factor (100Hz) 69 / - E-4 IEC 60250
Dissipation factor (1MHz) 69 / - E-4 IEC 60250
Volume resistivity >1E13 / 1E9 Ohm*m IEC 60093
Surface resistivity * / 1E14 Ohm IEC 60093
Electric strength 26 / - kV/mm IEC 60243-1
Comparative tracking index 600 / - - IEC 60112
Other propertiesdry / condUnitTest Standard
Water absorption 6.4 / * % Sim. to ISO 62
Humidity absorption 2.6 / * % Sim. to ISO 62
Density 1420 / - kg/m³ ISO 1183
Diagrams
Stress-strain , Zytel® HTN53G35HSLRHF BK083, PA*-GF35, DuPont
Stress-strain , Zytel® HTN53G35HSLRHF BK083, PA*-GF35, DuPont
Secant modulus-strain , Zytel® HTN53G35HSLRHF BK083, PA*-GF35, DuPont
Secant modulus-strain , Zytel® HTN53G35HSLRHF BK083, PA*-GF35, DuPont
Tensile modulus-temperature , Zytel® HTN53G35HSLRHF BK083, PA*-GF35, DuPont
Tensile modulus-temperature , Zytel® HTN53G35HSLRHF BK083, PA*-GF35, DuPont
LTHA-Stress at Break 4mm, Zytel® HTN53G35HSLRHF BK083, PA*-GF35, DuPont
LTHA-Strain at Break 4mm, Zytel® HTN53G35HSLRHF BK083, PA*-GF35, DuPont
LTHA-Charpy Impact Strength (23°C) 4mm, Zytel® HTN53G35HSLRHF BK083, PA*-GF35, DuPont
Characteristics
Processing
Injection Molding
Delivery form
Pellets
Additives
Lubricants, Release agent
Special Characteristics
Heat stabilized or stable to heat
Regional Availability
Other text information
Injection molding

PREPROCESSING


Drying Recommended = Yes, if moisture content of resin exceeds recommended level
Drying Temperature = 100°C
Drying Time, Dehumidified Dryer = 6-8 h
Processing Moisture Content = <0.1 %


PROCESSING


Melt Temperature Optimum = 290°C
Melt Temperature Range = 280-300°C
Mold Temperature Optimum = 95°C
Mold Temperature Range = 85-105°C


Moulding guide

Chemical Media Resistance
Acids
Acetic Acid (5% by mass) (23°C)
Citric Acid solution (10% by mass) (23°C)
Lactic Acid (10% by mass) (23°C)
Hydrochloric Acid (36% by mass) (23°C)
Nitric Acid (40% by mass) (23°C)
Sulfuric Acid (38% by mass) (23°C)
Sulfuric Acid (5% by mass) (23°C)
Chromic Acid solution (40% by mass) (23°C)
Bases
Sodium Hydroxide solution (35% by mass) (23°C)
Sodium Hydroxide solution (1% by mass) (23°C)
Ammonium Hydroxide solution (10% by mass) (23°C)
Alcohols
Isopropyl alcohol (23°C)
Methanol (23°C)
Ethanol (23°C)
Hydrocarbons
n-Hexane (23°C)
Toluene (23°C)
iso-Octane (23°C)
Ketones
Acetone (23°C)
Ethers
Diethyl ether (23°C)
Mineral oils
SAE 10W40 multigrade motor oil (23°C)
SAE 10W40 multigrade motor oil (130°C)
SAE 80/90 hypoid-gear oil (130°C)
Insulating Oil (23°C)
Standard Fuels
ISO 1817 Liquid 1 (60°C)
ISO 1817 Liquid 2 (60°C)
ISO 1817 Liquid 3 (60°C)
ISO 1817 Liquid 4 (60°C)
Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23°C)
Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (90°C)
Diesel fuel (pref. ISO 1817 Liquid F) (>90°C)
Salt solutions
Sodium Chloride solution (10% by mass) (23°C)
Sodium Hypochlorite solution (10% by mass) (23°C)
Sodium Carbonate solution (20% by mass) (23°C)
Sodium Carbonate solution (2% by mass) (23°C)
Zinc Chloride solution (50% by mass) (23°C)
Other
Ethyl Acetate (23°C)
Hydrogen peroxide (23°C)
DOT No. 4 Brake fluid (130°C)
Ethylene Glycol (50% by mass) in water (108°C)
1% nonylphenoxy-polyethyleneoxy ethanol in water (23°C)
50% Oleic acid + 50% Olive Oil (23°C)
Water (23°C)
Deionized water (90°C)
Phenol solution (5% by mass) (23°C)
Disclaimer

E.I. du Pont de Nemours and Company is pleased to provide information about its products with the CAMPUS electronic database.

The information provided is gratis and DuPont assumes no obligation or liability for any advice furnished or for any results obtained with respect to this information.

All such advice is given and accepted at the risk of the buyer. The disclosure of information herein is not an express or implied license to operate under any patent of DuPont or others.

DuPont warrants that the use or sale of any material which is described herein and is offered for sale by DuPont does not infringe any patent covering the material itself, but does not warrant against infringement by reason of the use thereof in combination with other materials or the operation of any process.

Unless otherwise noted, the property values are for natural color (NC010) resins only. Colorants or other additives may alter some or all of the properties.
The data listed herein fall within the normal range of product properties and they should not be used to establish specification limits nor used alone as the basis of design.

Material Safety Data Sheets (SDSs) can be obtained from local sales offices.

Products listed herein should not be used in medical applications involving permanent implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont under a written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use.

For further information, please contact your DuPont representative.

You may also request a copy of DuPont policy regarding medical applications H-50103-2 and DuPont caution regarding medical applications H-50102-2.

Products listed herein may from time to time be modified or removed.
Please call your local sales office to determine current availability.


The CAMPUS internet database is hosted by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

CAMPUS® is a Registered trademark of CWFG mbH, Frankfurt/Main, 1991