View list of
- All A. Schulman grades
- All PP grades
- All grades beginning with P
CAMPUS® datasheet | POLYFORT® FIPP 30 T K1005
This datasheet of POLYFORT® FIPP 30 T K1005 from A. Schulman GmbH is provided by the international plastics database CAMPUS.
You may contact the supplier for more information about this grade.
POLYFORT® FIPP 30 T K1005 | PP-T30 | A. Schulman GmbH
Texto del producto
30% talc filled PP copolymer compound
| Propiedades reológicas | Valor | Unidades | Método de ensayo |
| Indice de fluidez volumétrico, MVR | 6 | cm³/10min | ISO 1133 |
| Temperatura | 230 | °C | ISO 1133 |
| Carga | 2.16 | kg | ISO 1133 |
| Propiedades mecánicas | Valor | Unidades | Método de ensayo |
| Módulo de tracción | 2800 | MPa | ISO 527-1/-2 |
| Esfuerzo de fluencia | 27 | MPa | ISO 527-1/-2 |
| Alarg. en límite elástico | 3.5 | % | ISO 527-1/-2 |
| Alarg. nominal a rotura | 25 | % | ISO 527-1/-2 |
| Resistencia al impacto Charpy, +23°C | 55 | kJ/m² | ISO 179/1eU |
| Resistencia al impacto Charpy, -30°C | 19 | kJ/m² | ISO 179/1eU |
| Res. impacto Charpy c/entalla, +23°C | 7.5 | kJ/m² | ISO 179/1eA |
| Res. impacto Charpy c/entalla, -30°C | 4 | kJ/m² | ISO 179/1eA |
| Propiedades térmicas | Valor | Unidades | Método de ensayo |
| Temperatura de fusión, 10°C/min | 163 | °C | ISO 11357-1/-3 |
| Temp. de transición vítrea, 10°C/min | -20 | °C | ISO 11357-1/-2 |
| Estabilidad al calor, 1.80 MPa | 69 | °C | ISO 75-1/-2 |
| Estabilidad al calor, 0.45 MPa | 113 | °C | ISO 75-1/-2 |
| Temp. reblandecimiento Vicat, 50°C/h 50N | 66 | °C | ISO 306 |
| Coef.de expansión térmica lineal, paralelo | 80 | E-6/K | ISO 11359-1/-2 |
| Coef.de expansión térmica lineal, normal | 80 | E-6/K | ISO 11359-1/-2 |
| Propiedades eléctricas | Valor | Unidades | Método de ensayo |
| Constante dieléctrica, 100Hz | 2.9 | - | IEC 60250 |
| Constante dieléctrica, 1MHz | 2.9 | - | IEC 60250 |
| Factor de pérdidas dieléctricas, 100Hz | 30 | E-4 | IEC 60250 |
| Factor de pérdidas dieléctricas, 1MHz | 15 | E-4 | IEC 60250 |
| Resistividad volumétrica específica | >1E13 | Ohm*m | IEC 60093 |
| Resistividad superficial específica | >1E15 | Ohm | IEC 60093 |
| Otras propiedades | Valor | Unidades | Método de ensayo |
| Absorción de agua | 0.03 | % | Sim. to ISO 62 |
| Densidad | 1130 | kg/m³ | ISO 1183 |
| Cálculo propiedades reológicas | Valor | Unidades | Método de ensayo |
| Densidad de fusión | 900 | kg/m³ | - |
| Conductibilidad termica de fusión | 0.42 | W/(m K) | - |
| Difusibidad termica | 2.7E-7 | m²/s | - |
| Temperatura de expulsión | 100 | °C | - |
| Condiciones de transformación | Valor | Unidades | Método de ensayo |
| Condiciones de transformación según ISO | 1870 | - | ISO ....-2 |
| Moldeo por inyección, temperatura de la masa | 230 | °C | ISO 294 |
| Moldeo por inyección, temperatura del molde | 40 | °C | ISO 10724 |
| Moldeo por inyección, velocidad de inyección | 220 | mm/s | ISO 294 |
| Moldeo por inyección, presión de mantenimiento | 70 | MPa | ISO 294 |
Funciones
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Granulado
Aditivos
Desmoldeante
Características especiales
Antiestático, Estable contra el calor
Disponibilidad regional
Aviso
The information and recommendations contained in this document are based upon
data collected by A. Schulman and are believed to be reliable; however, because
A. Schulman cannot anticipate or control the many different conditions under
which this information and/or product may be used, no representation is made
and no warranty is given of any kind, express or implied, for completeness,
accuracy, availability, suitability, usefulness, commercial value, or non-violation
of intellectual property rights of information, recommendations, and products
and services directly or indirectly provided. A. Schulman assumes no responsibility
for the results of the use of products and processes described herein and expressly
disclaims the implied warranties of merchantability and fitness for a particular use
If there are questions to given information, to further properties or further A. Schulman
products please contact
A. Schulman GmbH
Huettenstrasse 211
50170 Kerpen
Tel: 02273 / 561-0
Contact: aschulman@de.aschulman.com
Subject: Material data
The CAMPUS internet database is hosted by M-Base Engineering + Software GmbH.
M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors.
Any decision about the application of materials must be double checked with the producer of this material.
CAMPUS® is a registered trademark of CWFG mbH, Frankfurt am Main, 2012
CAMPUS® is a registered trademark of CWFG mbH, Frankfurt am Main, 2012











