View list of
CAMPUS® datasheet | Durethan® BM 25 FN20 DUS013
This datasheet of Durethan® BM 25 FN20 DUS013 from LANXESS Deutschland GmbH is provided by the international plastics database CAMPUS.
Durethan® BM 25 FN20 DUS013 | PA6-MX25 FR | LANXESS Deutschland GmbH
Testo del prodotto
PA 6, 25 % mineral, injection moulding, halogen free flame retardant, optimized for laser marking (1064nm)
| Proprietà Reologiche | secco/cond | Unitá | Norma del test |
| Indice di fusione di volume, MVR | 27 / * | cm³/10min | ISO 1133 |
| Temperatura | 260 / * | °C | ISO 1133 |
| Carico | 5 / * | kg | ISO 1133 |
| Ritiro di stampaggio, parallelo | 0.9 / * | % | ISO 294-4, 2577 |
| Ritiro di stampaggio, perpendicolare | 0.9 / * | % | ISO 294-4, 2577 |
| Proprietà Meccaniche | secco/cond | Unitá | Norma del test |
| Modulo a trazione | 5700 / 2100 | MPa | ISO 527-1/-2 |
| Carico unitario a rottura | 80 / 30 | MPa | ISO 527-1/-2 |
| Deformazione a rottura | 3 / 50 | % | ISO 527-1/-2 |
| Resistenza all'urto Charpy, +23°C | 38 / 135 | kJ/m² | ISO 179/1eU |
| Proprietà Termiche | secco/cond | Unitá | Norma del test |
| Temperatura di fusione, 10°C/min | 220 / * | °C | ISO 11357-1/-3 |
| Temp.di inflessione sotto carico, 1.80 MPa | 90 / * | °C | ISO 75-1/-2 |
| Temp.di inflessione sotto carico, 0.45 MPa | 195 / * | °C | ISO 75-1/-2 |
| Coeff.di dilatazione termica lin., parallelo | 60 / * | E-6/K | ISO 11359-1/-2 |
| Coeff.di dilatazione termica lin., perpend. | 70 / * | E-6/K | ISO 11359-1/-2 |
| Reaz. al fuoco spess.nom. 1.5mm | V-2 / * | class | IEC 60695-11-10 |
| Spessore provato | 1.5 / * | mm | IEC 60695-11-10 |
| Reazione al fuoco a spessore h | V-2 / * | class | IEC 60695-11-10 |
| Spessore provato | 3.0 / * | mm | IEC 60695-11-10 |
| Proprietà Elettriche | secco/cond | Unitá | Norma del test |
| Res. Alle correnti striscianti superficiali | 450 / - | - | IEC 60112 |
| Altre Proprietà | secco/cond | Unitá | Norma del test |
| Assorbimento d'acqua | 6.7 / * | % | Sim. alla ISO 62 |
| Massa volumica | 1430 / - | kg/m³ | ISO 1183 |
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet
Disponibilità geografica
Disclaimer
This information and our technical advice - whether verbal, in writing or by way of trials - are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Our advice does not release you from the obligation to check its validity and to test our products as to their suitability for the intended processes and uses. The application, use and processing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and, therefore, entirely your own responsibility. Our products are sold in accordance with our General Conditions of Sale and Delivery. The values stored in the databank should only be used as guidelines for component design. In giving these values neither guarantee, nor assurance of particular material properties can be given. techcenter.lanxess.com
The CAMPUS internet database is hosted by M-Base Engineering + Software GmbH.
M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors.
Any decision about the application of materials must be double checked with the producer of this material.
CAMPUS® is a registered trademark of CWFG mbH, Frankfurt am Main, 2012
CAMPUS® is a registered trademark of CWFG mbH, Frankfurt am Main, 2012











