View list of
CAMPUS® datasheet | Durethan® A 30 H3.0
This datasheet of Durethan® A 30 H3.0 from LANXESS Deutschland GmbH is provided by the international plastics database CAMPUS.
Durethan® A 30 H3.0 | PA66 | LANXESS Deutschland GmbH
Informação do produto
PA 66, non-reinforced, injection moulding, heat-ageing stabilized
| Propriedades reológicas | Seco / Cond | Unidade | Método de ensaio |
| Contração após a moldagem, paralelo | 0.8 / * | % | ISO 294-4, 2577 |
| Contração após a moldagem, perpendicular | 0.9 / * | % | ISO 294-4, 2577 |
| Propriedades mecânicas | Seco / Cond | Unidade | Método de ensaio |
| Módulo de tração | 3500 / 1300 | MPa | ISO 527-1/-2 |
| Tensão no escoamento | 95 / 55 | MPa | ISO 527-1/-2 |
| Deformação no escoamento | 4.5 / 20 | % | ISO 527-1/-2 |
| Deformação nominal na ruptura | - / >50 | % | ISO 527-1/-2 |
| Resistência ao impacto Charpy , +23°C | 160 / 190 | kJ/m² | ISO 179/1eU |
| Resistência ao impacto Charpy, -30°C | 100 / 100 | kJ/m² | ISO 179/1eU |
| Res. impacto Charpy c/entalhe, +23°C | 10 / 20 | kJ/m² | ISO 179/1eA |
| Res. impacto Charpy c/entalhe, -30°C | 10 / 10 | kJ/m² | ISO 179/1eA |
| Propriedades térmicas | Seco / Cond | Unidade | Método de ensaio |
| Temperatura de fusão, 10°C/min | 261 / * | °C | ISO 11357-1/-3 |
| Temperatura de deflexão térmica, 1.80 MPa | 70 / * | °C | ISO 75-1/-2 |
| Temperatura de deflexão térmica, 0.45 MPa | 200 / * | °C | ISO 75-1/-2 |
| Coef. de expansão térmica linear, paralelo | 60 / * | E-6/K | ISO 11359-1/-2 |
| Coef. de expansão térmica linear, perpend. | 100 / * | E-6/K | ISO 11359-1/-2 |
| Propriedades elétricas | Seco / Cond | Unidade | Método de ensaio |
| Constante dielétrica, 100Hz | 3.8 / 13 | - | IEC 60250 |
| Constante dielétrica, 1MHz | 3.4 / 4.1 | - | IEC 60250 |
| Fator de dissipação dielétrica, 100Hz | 120 / 3200 | E-4 | IEC 60250 |
| Fator de dissipação dielétrica, 1MHz | 570 / 1000 | E-4 | IEC 60250 |
| Resistividade volumétrica específica | >1E13 / 1E10 | Ohm*m | IEC 60093 |
| Resistividade superficial específica | * / 1E13 | Ohm | IEC 60093 |
| Resistência elétrica | 31 / 25 | kV/mm | IEC 60243-1 |
| Índice comparativo de linha de fuga | 600 / - | - | IEC 60112 |
| Outras propriedades | Seco / Cond | Unidade | Método de ensaio |
| Absorção de água | 8.5 / * | % | Sim. to ISO 62 |
| Absorção de umidade | 2.8 / * | % | Sim. to ISO 62 |
| Densidade | 1140 / - | kg/m³ | ISO 1183 |
| Propriedades para cálculos reológicos | Valor | Unidade | Método de ensaio |
| Densidade do fundido | 970 | kg/m³ | - |
| Condutividade térmica do fundido | 0.225 | W/(m K) | - |
| Capacidade térmica específica do fundido | 2900 | J/(kg K) | - |
| Difusividade térmica | 8E-8 | m²/s | - |
| Temperatura de ejeção | 185 | °C | - |
| Produção de amostra para teste | Valor | Unidade | Método de ensaio |
| Moldagem por injeção, temperatura da massa | 280 | °C | ISO 294 |
| Moldagem por injeção, temperatura do molde | 80 | °C | ISO 10724 |
Características
Processamento
Moldagem por injeção
Forma de entrega
Granulos
Características especiais
Estável contra o calor
Disponibilidade regional
Disclaimer
This information and our technical advice - whether verbal, in writing or by way of trials - are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Our advice does not release you from the obligation to check its validity and to test our products as to their suitability for the intended processes and uses. The application, use and processing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and, therefore, entirely your own responsibility. Our products are sold in accordance with our General Conditions of Sale and Delivery. The values stored in the databank should only be used as guidelines for component design. In giving these values neither guarantee, nor assurance of particular material properties can be given. techcenter.lanxess.com
The CAMPUS internet database is hosted by M-Base Engineering + Software GmbH.
M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors.
Any decision about the application of materials must be double checked with the producer of this material.
CAMPUS® is a registered trademark of CWFG mbH, Frankfurt am Main, 2012
CAMPUS® is a registered trademark of CWFG mbH, Frankfurt am Main, 2012











